Engineering Mode


  • Ensure the main printer switch is off.
  • Hold "DOWN ARROW" and "RIGHT ARROW" buttons simultaneously, and switch on the main printer power.
  • Continue holding down buttons until screen displays "DIAGNOSTICS" menu.
  • Select the "REGISTRATION".
  • Select "LEFT MARGIN" 
  • Take note of value displayed. Reduce current value by 18 
    • eg. Initial value 4 change to -14. 
  • Save any change by selecting 'Tick' on printer buttons
  • Select "TOP MARGIN" option
    • Set Value as -13
  • Return "DIAGNOSTICS" then scroll to and select "EXIT DIAGNOSTICS", printer wil restart.


Configuration Mode

Config Auto Paper Size Sensing Option:

  • Ensure the main printer power switch is off.
  • Hold down the "TICK" button and the "RIGHT ARROW" button simultaneously, and then switch on the main printer power.
  • Continue holding these 2 buttons until the screen shows the "CONFIG MENU" menu.
  • Find and select the "SIZE SENSING" menu option.
  • Select the "TRAY 1 SENSING" menu option.
  • Select the "OFF" value. Remember to save the change by pressing the "TICK" button.
  • Return to the "CONFIG MENU" menu by selecting the "BACK" button.
  • Scroll down until you find the EXIT CONFIG MENU" menu option and select this. This will restart the printer.

Menu Options

Configure Print Area:

  • Printer ON
  • Press "MENU" button.
  • Find and select "SETTINGS"
  • Find and select "SETUP MENU"
  • Find and select "PRINT AREA"
  • Select "WHOLE PAGE" value. 
  • Press "TICK" button to save changes

Configure Paper Size/Type:

  • Press "MENU" button.
  • Find and select "SETTINGS"
  • Find and select "PAPER SIZE/TYPE"
  • Find and select "TRAY 1 SIZE/TYPE"
  • Select "UNIVERSAL"
  • Select "CARD STOCK"
  • Press "TICK" button to save changes


Configure Power Saver:

  • Select the "MENU" button.
  • Find and select the "SETTINGS" menu option.
  • Find and select the "GENERAL SETTINGS MENU" menu option.
  • Find and select the "TIMEOUTS" menu option.
  • Find and select the "POWER SAVER" menu option.
  • Select the desired minutes for the printer to wait in ready mode. Remember to save this by selecting the "TICK" button. Return to the "MENUS" by selecting the "MENU" button.


PC Settings - Adding The Printer


Adding the printer on the network:

  • Device type must be TCP/IP Device.
  • Add TCP/IP address select "NEXT".
  • Select "HAVE DISK" button.
  • Browse for the driver you downloaded on the PC and select it, remember it was downloaded to C:\Lexmark\Drivers\sysXL64Win. (my computer> C drive> Lexmark> Drivers> sysXL64Win > Drivers> Print> GDI> LMUD1P40.inf)
  • Once you have selected the driver, select "OK".
  • Make sure that the printer it found is the "Lexmark Universal v2 XL" and select the "NEXT" button.
  • Select "NEXT" again and the PC will start adding the printer, it will prompt you to share the printer or not, select share and "NEXT".
  • You have successfully added the printer to the PC on the Network.

Adding the printer via USB:

  • Keep "use an existing port" ticked and select the Virtual Printer Port For USB in the drop down and then select "NEXT".
  • Select the "HAVE DISK" button.
  • Browse for the driver you downloaded on the PC and select it, remember it was downloaded to C:\Lexmark\Drivers\sysXL64Win. (my computer> C drive> Lexmark> Drivers> sysXL64Win > Drivers> Print> GDI> LMUD1P40.inf)
  • Once you have selected the driver, select "OK".
  • Make sure that the printer it found is the "Lexmark Universal v2 XL" and select the "NEXT" button.
  • Select "NEXT" again and the PC will start adding the printer, it will prompt you to share the printer or not, select share and "NEXT".
  • You have successfully added the printer to the PC via USB.

Editing the Printer Preferences:

  • Navigate to the "CONTROL PANEL" > "DEVICES AND PRINTERS".
  • Right click on the Lexmark T652 printer and select "PRINTER PREFERENCES" in the drop down that appears.
  • Select landscape and Rotate 180 Degrees.
  • Click on the "PAPER/FINISHING" tab.
  • Click on "MANAGE CUSTOM PAPER SIZES". (If this option is not available then see below*) and then create "NEW" size.
  • Enter the following details:
    • Name: GasCard
    • Units: Millimetres
    • Width: 210mm
    • Height: 349mm.
  • Select OK -->CLOSE
  • Change PAPER SIZE to GasCard.
  • Change PAPER TYPE to Card Stock
  • Set PAPER SOURCE/TRAY to TRAY 1

Screenshot_3


Screenshot_6

Screenshot_7

Your PC and Printer should be ready for printing MiScore scorecards now.

Adjust any further settings to get the printer performing correctly.