Engineering Mode
Ensure the printer is offHold "DOWN ARROW" button AND "RIGHT ARROW" button simultaneously, and switch on the printer power.
Continue holding down buttons until screen shows "DIAGNOSTICS" menu.
Select "REGISTRATION" option
Select "LEFT MARGIN" option.
Take note of value displayed.
Use the left/right arrows to modify the value so that it is 18 more than the current value (or otherwise bring it back to 0)
Eg Value of -14, change it to be 4. Remember to save the change by pressing the "TICK" button. Please note: you may need to adjust this in order to get the card alignment printing in the centre of the page. Select the "TOP MARGIN" menu option. Take note of the value displayed. Use the left/right arrows to modify the value, save the value as 0 by selecting the "TICK" button once adjusted. Please note: you may need to adjust this in order to get the card alignment printing in the centre of the page. Return to the main "DIAGNOSTICS" menu by pressing the "BACK" button. Then scroll until you find the "EXIT DIAGNOSTICS" menu option and select this. This will restart the printer.
Configuration Mode Config Auto Paper Size Sensing Option: Ensure the main printer power switch is off. Hold down the "TICK" button and the "RIGHT ARROW" button simultaneously, and then switch on the main printer power. Continue holding these 2 buttons until the screen shows the "CONFIG MENU" menu. Find and select the "SIZE SENSING" menu option. Select the "TRAY 1 SENSING" menu option. Select the "OFF" value. Remember to save the change by pressing the "TICK" button. Return to the "CONFIG MENU" menu by selecting the "BACK" button. Scroll down until you find the EXIT CONFIG MENU" menu option and select this. This will restart the printer.
Menu Options Configure Print Area: The main printer power switch must be on. Select the "MENU" button. Find and select the the "SETTINGS" menu option. Find and select the "SETUP MENU" menu option. Find and select the "PRINT AREA" menu option. Select the "WHOLE PAGE" value. Remember to save the change by pressing the "TICK" button. Return to the "MENUS" menu by pressing the "MENU" button. Configure Paper Size/Type: Select the "MENU" button. Find and select the "SETTINGS" menu option. Find and select the "PAPER SIZE/TYPE" menu option. Find and select the "TRAY 1 SIZE/TYPE" menu option. Select the "A5" option. Next select the "CARD STOCK" value. Return to the "MENUS" menu by pressing the "MENU" button. Configure Power Saver: Select the "MENU" button. Find and select the "SETTINGS" menu option. Find and select the "GENERAL SETTINGS MENU" menu option. Find and select the "TIMEOUTS" menu option. Find and select the "POWER SAVER" menu option. Select the desired minutes for the printer to wait in ready mode. Remember to save this by selecting the "TICK" button. Return to the "MENUS" by selecting the "MENU" button.
PC Settings - Adding The Printer On the PC, open up a fresh internet page (preferably in Google Chrome). In the URL/Address bar at the top of the page, type in support.miclub.com.au/gas and press enter. Select the "Printer_Drivers" link. Select the "Lexmark T652" driver option. Select which version you need dependent on the PC type, the 32bit or the 64bit. (To find out what version you need for that PC you can right click on the "MY COMPUTER" file (found in the "FILE EXPLORER" file on the desktop) and select the "PROPERTIES" option in the drop down that appears. This will tell you what printer driver version you need to select) Once your have selected the printer version, it will start to download on the PC. (if using Chrome you will see the printer driver downloading in the bottom left of the page) 
Select and run the printer driver once it has finished downloading. (if not using Chrome, go to the downloads file on the PC and select and run the printer driver) The PC will then prompt you to start the process of adding the printer. Agree to the "LICENSE AGREEMENT". Make sure the "EXTRACT and INSTALL" option is selected and the driver is being stored in C:\Lexmark\Drivers\sysXL64Win, click on the "INSTALL" button. Click on blue text/link in the bottom left of the box "THE PRINTER THAT I WANT ISN'T LISTED". Choose whether you are adding the printer via USB (local) or over the network (via a TCP/IP address). Adding the printer on the network: Device type must be TCP/IP Device. Put the printers TCP/IP address in the Hostname or IP address section and select "NEXT". Select the "HAVE DISK" button. Browse for the driver you downloaded on the PC and select it, remember it was downloaded to C:\Lexmark\Drivers\sysXL64Win. (my computer> C drive> Lexmark> Drivers> sysXL64Win > Drivers> Print> GDI> LMUD1P40.inf) Once you have selected the driver, select "OK". Make sure that the printer it found is the "Lexmark Universal v2 XL" and select the "NEXT" button. Select "NEXT" again and the PC will start adding the printer, it will prompt you to share the printer or not, select share and "NEXT". You have successfully added the printer to the PC on the Network. Adding the printer via USB: Keep "use an existing port" ticked and select the Virtual Printer Port For USB in the drop down and then select "NEXT". Select the "HAVE DISK" button. Browse for the driver you downloaded on the PC and select it, remember it was downloaded to C:\Lexmark\Drivers\sysXL64Win. (my computer> C drive> Lexmark> Drivers> sysXL64Win > Drivers> Print> GDI> LMUD1P40.inf) Once you have selected the driver, select "OK". Make sure that the printer it found is the "Lexmark Universal v2 XL" and select the "NEXT" button. Select "NEXT" again and the PC will start adding the printer, it will prompt you to share the printer or not, select share and "NEXT". You have successfully added the printer to the PC via USB. Editing the Printer Preferences: Navigate to the "CONTROL PANEL" > "DEVICES AND PRINTERS". Right click on the Lexmark T652 printer and select "PRINTER PREFERENCES" in the drop down that appears. 
Click on the "PAPER/FINISHING" tab. Make sure the "PAPER SIZE" is set to "A5". Make sure the "PAPER TYPE" is set to "USE PRINTER SETTINGS" Make sure the "PAPER SOURCE/TRAY" is set to "TRAY 1". 
Your PC and Printer should be ready for printing MiScore scorecards now. Adjust any further settings to get the printer performing correctly.
Select and run the printer driver once it has finished downloading. (if not using Chrome, go to the downloads file on the PC and select and run the printer driver) The PC will then prompt you to start the process of adding the printer. Agree to the "LICENSE AGREEMENT". Make sure the "EXTRACT and INSTALL" option is selected and the driver is being stored in C:\Lexmark\Drivers\sysXL64Win, click on the "INSTALL" button. Click on blue text/link in the bottom left of the box "THE PRINTER THAT I WANT ISN'T LISTED". Choose whether you are adding the printer via USB (local) or over the network (via a TCP/IP address). Adding the printer on the network: Device type must be TCP/IP Device. Put the printers TCP/IP address in the Hostname or IP address section and select "NEXT". Select the "HAVE DISK" button. Browse for the driver you downloaded on the PC and select it, remember it was downloaded to C:\Lexmark\Drivers\sysXL64Win. (my computer> C drive> Lexmark> Drivers> sysXL64Win > Drivers> Print> GDI> LMUD1P40.inf) Once you have selected the driver, select "OK". Make sure that the printer it found is the "Lexmark Universal v2 XL" and select the "NEXT" button. Select "NEXT" again and the PC will start adding the printer, it will prompt you to share the printer or not, select share and "NEXT". You have successfully added the printer to the PC on the Network. Adding the printer via USB: Keep "use an existing port" ticked and select the Virtual Printer Port For USB in the drop down and then select "NEXT". Select the "HAVE DISK" button. Browse for the driver you downloaded on the PC and select it, remember it was downloaded to C:\Lexmark\Drivers\sysXL64Win. (my computer> C drive> Lexmark> Drivers> sysXL64Win > Drivers> Print> GDI> LMUD1P40.inf) Once you have selected the driver, select "OK". Make sure that the printer it found is the "Lexmark Universal v2 XL" and select the "NEXT" button. Select "NEXT" again and the PC will start adding the printer, it will prompt you to share the printer or not, select share and "NEXT". You have successfully added the printer to the PC via USB. Editing the Printer Preferences: Navigate to the "CONTROL PANEL" > "DEVICES AND PRINTERS". Right click on the Lexmark T652 printer and select "PRINTER PREFERENCES" in the drop down that appears. Click on the "PAPER/FINISHING" tab. Make sure the "PAPER SIZE" is set to "A5". Make sure the "PAPER TYPE" is set to "USE PRINTER SETTINGS" Make sure the "PAPER SOURCE/TRAY" is set to "TRAY 1". Your PC and Printer should be ready for printing MiScore scorecards now. Adjust any further settings to get the printer performing correctly.Was this article helpful?
That’s Great!
Thank you for your feedback
Sorry! We couldn't be helpful
Thank you for your feedback
Feedback sent
We appreciate your effort and will try to fix the article